SEASONAL MAINTENANCETHE IGARDEN GLOSSARY

Pool Closing

Learn how to close a swimming pool in Australia with practical advice on water balancing, pool cleaning, chemical treatment, equipment protection and winterisation. Discover the essential steps for preparing your pool for seasonal shutdown while protecting water quality and avoiding costly damage.

Updated 2026-11-16

Pool closing is the process of preparing a swimming pool for an extended period of reduced use or temporary shutdown. It involves cleaning the pool, balancing the water, preparing filtration and sanitising systems, and protecting equipment from seasonal weather conditions.

In Australia, pool closing requirements vary considerably between regions. Some pools remain in operation throughout the year, while others require seasonal adjustments or more extensive winterisation to protect pumps, filters and exposed plumbing from frost.

A proper swimming pool closing procedure does not normally involve draining the pool or stopping all maintenance. The objective is to keep the water in a manageable condition, reduce unnecessary equipment operation and prevent problems that could make reopening more difficult.

When Should You Close a Swimming Pool?

The timing of pool closing depends more on local weather conditions and swimming habits than on a particular calendar date.

In tropical and subtropical parts of Australia, including much of Queensland and northern Australia, swimming pools can often remain operational throughout the year. Owners may only need to reduce filtration hours and adjust chemical dosing as water temperatures and swimming frequency change.

In temperate regions such as Victoria, Tasmania and parts of New South Wales, swimming activity generally decreases during winter. Lower water temperatures also reduce algae growth and chlorine consumption, making seasonal adjustments to filtration and sanitisation practical.

Frost-prone inland areas require additional consideration. Exposed pipes, pump housings, filters and other equipment containing water may be damaged if temperatures fall below freezing.

Pool owners should also consider seasonal preparation when the property will be unoccupied for several weeks or months, swimming activity has stopped for an extended period, or equipment needs protection during colder weather.

There are three common approaches:

  • Temporary shutdown: The pool remains maintained, with normal or reduced filtration and sanitisation.

  • Seasonal pool closing: Filtration and chemical dosing are adjusted to suit colder weather and reduced use.

  • Full winterisation: Equipment and vulnerable plumbing are prepared for an extended shutdown, particularly where freezing conditions are expected.

These approaches require different levels of preparation. A pool in Brisbane does not necessarily need the same winterisation procedure as one in regional Victoria.

What to Do Before Closing a Pool

Cleaning should be completed before reducing filtration or shutting down equipment. Organic debris left in the water can decompose, consume sanitiser and contribute to algae growth.

Start by removing leaves, insects, twigs and other floating debris with a pool leaf rake or skimmer net. Brush the walls, steps, corners and floor to loosen dirt and early algae deposits. Vacuum the pool to remove material that has settled on the bottom.

Pay particular attention to areas around steps, corners and fittings where debris can accumulate. If algae is already present, treat the affected areas before proceeding with seasonal shutdown.

The aim is to leave the pool as clean as possible before reducing its normal maintenance routine.

Balance Pool Water Before Closing

Water chemistry should be tested and adjusted before seasonal shutdown. Closing a pool with poorly balanced water can contribute to surface staining, corrosion, scale formation and algae growth during periods of reduced circulation.

The main parameters to check are:

Parameter General Australian guidance Purpose
pH 7.2–7.6 Supports effective sanitisation and protects surfaces
Free Chlorine Depends on stabiliser, water temperature and sanitising system Maintains disinfection
Total Alkalinity Approximately 100–120 mg/L; broader recommended range 60–200 mg/L Helps stabilise pH
Calcium Hardness Approximately 80–500 mg/L Helps maintain water balance and protect surfaces
Cyanuric Acid (CYA) 30–50 mg/L for suitable outdoor chlorine pools Protects chlorine from UV degradation

These are general reference values, not universal targets for every pool. SPASA references AS 3633 for several of these operating ranges, while individual pool surface and equipment manufacturers may specify different targets.

Free chlorine requires particular attention. Its appropriate level depends on the sanitising system, cyanuric acid concentration and water temperature. For example, HealthyWA guidance for stabilised outdoor pools specifies minimum free chlorine levels of 2 mg/L below 26°C and 3 mg/L above 26°C. These figures should not be treated as a universal domestic pool closing formula.

Cyanuric acid should also be checked in outdoor pools using chlorine stabiliser. Excessive stabiliser accumulation can reduce chlorine effectiveness, while insufficient stabiliser allows sunlight to break down chlorine more rapidly.

Total alkalinity and calcium hardness contribute to overall water balance. Low alkalinity can cause unstable pH readings, while unsuitable calcium levels can contribute to either corrosive water or mineral scale.

Adjust the parameters using measured results rather than adding chemicals as a precaution. Allow the water to circulate after adjustments and retest to confirm the results.

Sources: SPASA, Water Balance; HealthyWA, Swimming Pools and Spas.

Pool Closing Chemicals: What Should You Use?

The chemicals required for pool closing depend on the existing water condition, the sanitising system and how long the pool will remain unattended.

Pool sanitiser and chlorine remain important even when the pool is not being used. Reduced filtration does not remove the need to maintain an appropriate disinfectant residual. Chlorine consumption usually decreases as water temperatures fall, but it does not necessarily stop.

Pool shock treatment may be appropriate before closing if testing indicates low sanitiser levels, high combined chlorine or significant organic contamination. A shock treatment helps oxidise accumulated contaminants, but it should not be applied automatically to every pool. Follow the product label and allow the required circulation time.

Algaecide can provide additional protection where appropriate, particularly in pools exposed to sunlight or with a history of algae problems. Choose a formulation compatible with the pool surface and existing sanitising system. It is not a replacement for maintaining chlorine levels.

pH and alkalinity adjustment chemicals should be used only when test results indicate that correction is necessary. Sodium bicarbonate is commonly used to increase total alkalinity, while suitable acid products can reduce pH.

Never mix pool chemicals together or combine concentrated chlorine and acid. Add products separately according to their instructions, using the specified dilution and circulation procedures.

How to Prepare Pool Equipment for Closing

Equipment preparation depends on whether the pool will continue circulating or undergo a full seasonal shutdown. Before reducing filtration, clean the components that collect debris and check that the system is operating correctly.

Pool pump: Empty the pump strainer basket and inspect the lid seal for wear or damage. Check for leaks, unusual noises and problems with priming. If the pump will remain operational, confirm that it maintains adequate circulation. For an extended shutdown in a frost-prone area, isolate the equipment and drain the pump housing as instructed by its manufacturer.

Sand, cartridge and DE filters: Clean the filter before reducing operation. Sand filters may require backwashing and rinsing, while cartridge filters should be removed and cleaned using the manufacturer's recommended procedure. DE filters require appropriate cleaning and recharging when returned to service. Check the pressure gauge, valves and drain fittings for signs of damage.

Pool heater: Switch off the heater according to its operating instructions. Where frost is expected, the heat exchanger and associated plumbing may require draining or other manufacturer-approved protection. Gas and fixed electrical equipment should be serviced by appropriately licensed professionals.

Saltwater chlorinator: Inspect the electrolytic cell for calcium deposits and clean it using an approved procedure if necessary. Some salt chlorinators reduce or stop chlorine production when water temperatures fall below their specified operating threshold. Adjust or isolate the system according to its manual, while making sure the pool retains adequate sanitiser.

Automatic pool cleaner: Remove the cleaner from the water, clear debris from its components and inspect its brushes, tracks and hoses. Store robotic cleaners and their power supplies in a dry, sheltered location, following the manufacturer's storage instructions.

Pipes and valves: Exposed plumbing requires particular attention in frost-prone regions. Insulate vulnerable sections where appropriate and drain equipment or pipework where the winterisation procedure requires it. Do not use compressed air to clear plumbing unless the system manufacturer specifically permits the method and it is carried out safely.

Fixed electrical work and equipment repairs should be handled by appropriately licensed tradespeople.

Pool Closing Basics

Should You Lower the Pool Water Level?

Lowering the water level is not a standard requirement for pool closing in Australia. Most residential pools should remain filled during seasonal shutdown.

Under normal operating conditions, the water level should generally sit around the middle of the skimmer box opening. This allows the skimmer to collect floating debris while maintaining adequate water supply to the pump.

Heavy rainfall may cause the level to rise, particularly when a pool is covered or surrounded by surfaces that direct stormwater towards it. Monitor the level and use the appropriate drainage arrangements if it approaches the overflow point.

In frost-prone areas, some equipment winterisation procedures require the water level to be lowered below the skimmer or return fittings. This should only be done when specified by the pool manufacturer or an experienced pool technician.

Pool construction also matters. Fibreglass shells can move or become distorted when groundwater pressure exceeds the support provided by the water inside the pool. Concrete pools are not immune to hydrostatic pressure, and emptying them can also cause structural damage.

Completely draining a pool without professional assessment is therefore not recommended. The City of Gold Coast specifically warns that removing pool water can cause structural failure, including fibreglass pools lifting under surrounding soil pressure.

Pool Covers and Seasonal Protection

A suitable pool cover helps protect the water during periods of reduced use.

A cover limits leaves, insects and other debris entering the pool. Depending on its material and design, it can also reduce evaporation and help retain heat.

Opaque covers reduce the amount of sunlight reaching the water, which can help limit algae growth. However, transparent solar blankets may allow sunlight through and can increase the temperature of the surface water. Water chemistry and sanitisation still need to be maintained.

Before installing a cover, remove accumulated debris and check that the water level is appropriate. Make sure the cover is securely fitted and suitable for the pool's shape and dimensions.

An ordinary pool cover is not a substitute for a compliant pool safety barrier. Australian pool owners must continue to maintain the legally required fencing, gates and other safety measures throughout the shutdown period. Pool safety requirements vary between states and territories.

Source: SA Government, Pool and Spa Safety.

Pool Closing Checklist

Use this checklist when preparing a swimming pool for seasonal shutdown.

Task Purpose
Remove leaves and debris Reduce organic contamination
Brush and vacuum the pool Remove dirt and early algae deposits
Test and balance water Maintain suitable water conditions
Clean skimmer and pump baskets Prevent blockages
Clean filters Prepare filtration equipment
Inspect pumps and plumbing Identify leaks and existing problems
Prepare sanitising equipment Follow the appropriate shutdown procedure
Protect exposed equipment Reduce frost and weather-related damage
Check water level Maintain suitable operating conditions
Install a suitable pool cover Limit debris and sunlight exposure
Schedule periodic inspections Identify problems during the shutdown

Common Pool Closing Mistakes

Some pool closing mistakes result from applying winterisation practices without considering the pool's construction, climate or sanitising system.

Draining the pool without assessing groundwater conditions

Removing pool water can expose the shell to external groundwater pressure. Fibreglass pools are particularly vulnerable to lifting or movement, while concrete structures can also suffer damage. Keep the pool filled unless a qualified pool professional confirms that draining is necessary.

Assuming a pool cover eliminates the need for maintenance

A cover reduces debris and sunlight exposure, but it does not maintain chlorine levels or prevent all algae growth. Water chemistry can still deteriorate during an extended shutdown, so periodic testing and sanitiser adjustments remain necessary.

Forgetting to maintain chlorine after a saltwater chlorinator stops producing it

Some saltwater chlorinators reduce or stop production when water temperatures fall below their operating threshold. If the pool continues to be maintained during this period, owners may need to switch to a compatible manual chlorine treatment to maintain the required sanitiser level.

Adding excessive chemicals before shutdown

Adding shock, algaecide or other products without testing can create chemical imbalances and potentially damage pool surfaces or equipment. Seasonal treatment should be based on actual water conditions and product instructions, not a fixed combination of closing chemicals.

Preparing to Reopen Your Pool

When warmer weather returns, remove and clean the pool cover, inspect the equipment and restore normal water circulation. Test and balance the water, recommission the sanitising system and confirm that the pool is clear with appropriate sanitiser levels before swimming. For a complete seasonal startup procedure, see our step-by-step guide, How to Reopen Your Pool for Summer.